Messages

Another thing, would it be possible to set and save the dashboards depending on the activity? Further it is only possible to set the dashboards when the recording is running. It is not possible to set the dashboards before.

I use Nokia 7 Plus with Android 8.1 as Pure Android or Android One.

As Smartwatch I use the Polar M600 with current WearOS version. I can find out the exact version this evening.

On Polar M600 is Wear OS 1.5
HomeApp 2.15
Android 8.0
Security Patche  from 5.August 2018

On the Smartwatch the power saving function is deactivated.

I am always happy when I get positive feedback. This can narrow errors and exclude certain constellations.

Yesterday I had the problem that the connection or recording was not continuous. Presumably, this is due to the low battery level on the smartwatch.

But I have to verify that again.

I'll let you know.

I use Nokia 7 Plus with Android 8.1 as Pure Android or Android One.

As Smartwatch I use the Polar M600 with current WearOS version. I can find out the exact version this evening.

Am I the only one where it works reasonably well?

Best Regards
Danjel

Hello, Milan,

today I could test the pulse measurement again in bicycle mode. I rode my bike for about 50min and only had a drop-out of 10 seconds. Otherwise the transmission worked perfectly.

Best Regards
Danjel Rojka

Hello Milan,

the interruption of the cardiac frequency has only one interruption in an hour.
At 54min 26sec to 54min 46sec

Otherwise, I have a continuous transmission.

Best Regards
Danjel Rojka

No, I don't know.

I couldn't tell because I wasn't looking at the dashboard all the time. I'll check it on the next run to see if it happens.

You mean the dashboard on the Smartwatch or on the smartphone?

I can report that Wear Locus works without problems.
The heart rate was reproduced by Wear Locus without any problems. And I was able to finish my run successfully with the lap announcement and the heart rate message every 3min.
At the same time I started the Polar App on the Smartwatch and started the recording there. Both ran parallel and had no problems.

ˊ ` ` ` ` ` ` ` ` ` ` ` ` ` ` `'F'¯'''''L ` ` ` ` ` ` ` ` ` ` ` `
` ` ` ` ` ` ` ` ` ` ` ` ` ` ` `'[``...'¾`` ``` ``` ``` ```
` ` ` ` ` ` ` ` ` ` ` ` ` ` ` `'[```...ʹ[` ` ` ` ``` ``` ```
` ` ` ` ` ` ` ` ` ` ` ` ` ` ` `#````ˆ[```` ``` ``` ``` ``
` ` ` ` ` ` ` ` ` ` ` ` ` ` `'#``...``'[`... ` ` ` ` ` ` ` ` `
` ` ` ` ` ` ` ` ` ` ` ` ` ` #...`````'F`` ` ` ` `` ``` ```
` ` ` ` ` ` ` ` ` ` ` ` ` ƒ¯```````'[__` ` ` ` ` ` ` ``` ``
` ` ` ` ` ` ` ` ` ` ` ` ƒ¯````````ʹ¯¯¯¯''''''''''''¯¯¯¯¯¯™[ `
gµµµµµµµµµµµµµµ_µ™`````````````````````````'# `
'₫₫₫₫₫₫₫₫₫₫₫₫₫F¯...`````````````````````` ` ²q[¯ ` `
ʹ₫₫₫₫₫₫₫₫₫₫₫₫¾````````````````````````````ʹ} ... `
›₫₫₫₫₫₫₫₫₫₫₫₫#`````````````````````````__µr... ` `
³₫₫₫₫₫₫₫₫₫₫₫₫₫...`````````````````````````¯[ ... ` `
`₫₫₫₫₫₫₫₫₫₫₫₫$``````````````````````````_F ... ` `
`]₫₫₫₫₫₫₫₫₫₫₫#````````````````````````ʹ''''[... ... ` `
`'₫₫₫₫₫₫₫F''''']₫#___`````````````````````` '# ... ` `
...₫₫₫₫₫₫₫bµ₫₫₫₫$¯''''¹uuuuuɷuɷuɷuɷuɷuɷµ#¯ ` ` ` ` `
...'''''''™''''™'''™''''™™ ... ... ` ` ` ` ` ` ` ` ` ` ` ` ... ... ` ` `
` ... ` ` ` ` ` ` ` ` ... ` ... ` ` ` ` ` ` ` ` ` ` ` ... ` ` ` ` `.

Hello Milan, I didn't find the time to install the beta. Should I do this after the fact?
Or is the problem fixed?

regards
Danjel

Hello Milan,

On Saturday I tested the function outside and I had good GPS reception. I had the same issue.

Regards
Danjel

Hello, Milan,
I have configured another sensor. This is the Mio link I connected via Bluetooth. But I also deactivated Bluetooth in Locus for connection with Mio when I started recording. With no other result. And Mio wasn't activated and connected either.

Hello, Milan,

the screenshot does not always show the 3rd value with 4 but it is as you describe at 1 or 2 and also the first value is usually at 3.

Hello, Milan,

I uninstalled and restarted the app on the Watch. I did not uninstall the app on my smartphone but on my watch. Then reinstalled. Still no pulse display with values.

Then I activated the debug mode as shown by you and activated the heart rate (debug) in the dashboard.

He shows me the following values as in the screenshot.

That's all I know.

Danjel