[APP] - version 3.19.x (12. 10. 2016+)

[Andrew Heard]

2) profiles are stored internally ... I've attached current version to this post below. Few available parameters ( %avoid_motorways%, %avoid_toll%, %avoid_unpaved% and %is_wet% ) are currently hardcoded in Locus.

@menion - that's great - I can extract a BRF file from your Locus ZIP, copy to the BRouter profiles2 folder, and now Locus advanced navigation settings will parse the special "hard coded" parameters and display equivalent checkboxes - very nice!

[Menion]

@balloni55: hmm this is currently not possible, sorry

@0709: understand, thanks. I've added support "PassPlace.ogg" sound file for these cases, so try it with next version, should work.

@TrulloF: sorry, I don't understand what is wrong on Locus side. Write me please exact steps I may follow to get this behavior, thanks

@Andrew Heard: oki

[lor74cas]

Hello
In map items I found a double voice in menu one in English and one in Italian.
The Italian one is enabled the English disabled but the line is visible on the map.


Inviato dal mio SM-G800F utilizzando Tapatalk

[TrulloF]

If you use the brouter approach of naming the start and end points "from" and "to" and during navigation a recalculation of the route is necessary you get the shown error message and automatic recalculation is not possible anymore.

[jusc]

Here's a screen shot of the error, when using "to" and "from" points as start and target for navigation with brouter and recalculation is kicking in.

Do you have more than one folder of points? I had the same problem. After disabling one " to and from point set" in one of 8 folders, it works now.

[Christian]

Wanted to try the new "measurement with two fingers" but nothing happend. Whats wrong?

[balloni55]

@ Christian
settings/maps/Maps objects/Quick measure
enabled??

[lor74cas]

Wanted to try the new "measurement with two fingers" but nothing happend. Whats wrong?

http://help.locusmap.eu/topic/measuring-distances-with-two-fingers-on-the-screen

Settings -> Maps -> Map Objects -> Quick Measurement. (Enable)
photo
0709
2 days ago

Inviato dal mio SM-G800F utilizzando Tapatalk

[TrulloF]

I use the quick add point function, which stores "from" and "to" into a subfolder. It's pretty obvious, that this is a problem now, but it was working until the last stable version.

Here's a screen shot of the error, when using "to" and "from" points as start and target for navigation with brouter and recalculation is kicking in.

Do you have more than one folder of points? I had the same problem. After disabling one " to and from point set" in one of 8 folders, it works now.

[Christian]

Thanx guys.

[poutnikl]

@menion - that's great - I can extract a BRF file from your Locus ZIP, copy to the BRouter profiles2 folder, and now Locus advanced navigation settings will parse the special "hard coded" parameters and display equivalent checkboxes - very nice!

Hi Andrew,
you can get the current profile versions from https://github.com/poutnikl/Brouter-profiles/wiki, as they are subjects of occasional change.

[Andrew Heard]

Thanks, I knew that, but wasn't sure (until Menion's reply) where the internal Locus "BRF" files were stored. I now think it is a great solution. Well done you & @menion.

[zossebart]

I very much like the new BRouter navigation settings. Good result after a few beta trials.

Me too! Great Solution! Not only do I have more "slots" for profiles in the routing mode selection, but also the free naming and of course the ability to use profile flags (although only the 4 pre-defined ones) is great!
Thank you, this is a really nice enhancement!

Regards,
Zossebart

[Bango903]

omg, smth went wrong with last update! I update my app and can't lounch it now! I need to use bluestacks http://android-emulator.net/en/bluestacks.php to lounch it and can't downgrade! What to do??

[Joachim Buhl]

Hello Menion

Please change something to hide the via points again. It doesn't make any sense:


Thanks