Messages

Is it possible you have in Settings/GPS & sensors set Google Services assisted location
and at the same time in Setting track recording / recording profile
you do not have set reasonable limit for location accuracy, e.g. 50 m ?

Thanks and yes, Google Services is active ... I thought this was the best setting. Changed it ... but btw.  when should it be used?
Accuracy is set to even 20m, filtering to middle ... just to prevent the above problem.

Just see what happens tomorrow ...

Sometimes I have some peaks/GPS runaways in my tracks ...
I examined my settings and found no problem. Today I had the runaways again ... and as the picture shows: all in connection with a cache.
What I did: navigating along a route and some meters before reaching the cache use Locus compass to show distance to cache.
Maybe this caused the problem?

Weird ... on my tablet it's working. On my mobile S10e it doesn't.

With new version now it's working on my mobile too. 😎👍

Here long-press-menu ...

Weird ... on my tablet it's working. On my mobile S10e it doesn't. 🤔

How can I start expert settings?
Long press menu doesn't work ... 😨

Today I was navigating along a route ... and had several problems:
- navigation has stopped several times while searching (with compass) a geocache
- two or three time Locus started completely new (track recording was continued, navigation had to be started manual)

Because all this is not repeatable by a single action ... is there a logfile where problems are documented?

PS: maybe some problems are caused from screen lock (I use basic lock) . With this lock it's always a little bit weird ... but finaly it works while driving.

PSPS: during my tour today I didn't use lock screen and geocaching - just navigating - and all works great over 3h and 140km 😎

@jonny.blue
The geocaching part of the new point screen is definitely not finished. The current state is work-in-progress. So if, I will appreciate some feedback based on work with all points except geocaching .

... ohhh, just forgot. 😚

They are not visible right when this screen displays?

Finaly found it out after switching one by one option:
when you set 'display->full screen ... not only notification bar disappears but also bottom panel of this popup.

They are not visible right when this screen displays?

Yes, with one preset the panel is (almost 🤔 ) hidden.
I tried a little bit to touch the area ... and when I hit a place where a butten shoud be ... it works.
It seems as if the panel is compressed.
... and after some attempts it appears partially.

 

And today ... I had several crashes where Locus completely exited.

The most problems are arround the new geocache card.
I have two presets ... with one I can see the bottom panel ... with the other it mostly disappeares (its my driving setup where orientation is blocked, looking into driving direction ...and more).
There I can reproduce the crash: within the new cache card turning the mobile leads directly to the exception.
Btw ... the new geocache popup isn't really good for caching because all actions (navigate, compass, hint, log ... are far away🤔).

After month of (couch ) testing with tablet last week I decided to take LM to productive mode with my mobile.
After some hiking tours, some geocaches ... and today a cool bike tour with navigating along a route ... the main functions are working pretty good. 😎
The only thing I had to fight with today ... the bottom of the geocaching card disappears sometimes 🤔 ... and then it was not easy to get into the cache screen.

Crash directy after Startup.

... same here.

A suggestion for the planner:
sometimes I need to switch from automatic to manual design because not all tracks are mapped.

I would appreciate a faster solution too ... 

In many hiking areas routing isn't continuously possible because there seems to be unpassable parts (often bridges or a change of path or just map failures) .. so a faster solution would be very helpful.

Yes ... search is great ... and will save a lot of time. 😉

With one search I found a strange behaviour:
When searching for " audio" and then selecting "audio trainer" Locus shows a new screen ... and stops. 😯