Messages

maybe little bit complicated but working solution

1. go to POI manager screen
2. tap fitler and check hide found
3. now select all (2nd button)
4. tap filter again and uncheck hide found
5. invert filter now (3rd button)
6. move selected points to another category (last button > move)

Hi Arcao, last market version already use this API

jojo ten problém je v rozbalování toho zipu s diakritikou. Tam to hodí error. Samotný import data ze souboru je pak bez problému

ohledně vyhledávání. V locusu to zatím nejde (časem snad půjde) ale co vím, tak tuhle funčnost mají obvykle placené navigace případně nějaké volně ke stažení, ale rozhodně bych hledal offline vyhledávání address u navigačních programů. Zkušenost s tím ale nemám .. viva papírové mapy. Jak píšeš, baterie nikdy nedojdou

Hi guys,
  I'm sorry but I still have no simple solution for this. Size of buttons is set in one configuration file during compiling of application and I have no idea how to change it dynamically during app run, so this is currently not possible

ah good point rijackson. I'll look on both issues.

about deviations. I'm using special least square method. Three points are minimum so deviation on them will be very low. Best is to use four or more points to get best results

you can see exact memory stats ... I leave enabled personal log messages just for this case. Hmm there is probably problem that you calibrated map before, then you display it on map and then you go back to on-board calibration screen that loaded previous calibration session ...

this will be very dangerous function and I'm sure, I'll receive many info that it do not work and only crashing . Hmm one solution should be separate map into pieces and pack it to tar archive but it will lost kmz file format which I don't want ..., damn phone memory limits ...

tak jsem si s tím hrál a problém nalezen. Jen nevím jak ho opravit ..

každopádně když se zbavíš diakritiky ve jménech souborů tak to pojede, tzn. Nádraží.kml jen jako Nadrazi.kml a tak dále ...

háže to chybu v jedné systémové funkci a nedaří se mi najít nějaké řešení. Takže zatím tak ...

ah good news ...

so stebu .. the errors are only out of memory? I'm sorry but it's problem with your phone. I expect that zte blade allow only 16MB of memory for application. For unknown reason, Locus takes 5MB in moment it start (cannot figure out why .. maybe too much languages? have to try someday) and next 4MB till fully initialized (without any extra points or tracks loaded). So it leave only 7MB to whole calibration and it's really tooo looow. "Small" disadvantage of program complexity compare to specialized programs

InFX ... as I wrote. calibrated maps are then saved into locus/mapItems directory. Did "Map item manager" works for you? If so, you should there see all available and loaded maps ...

hendo ... you understand correctly. Did you tried this function? I think that whole system is pretty easy so I'm sure you'll understand how this works. Function is accessible from menu > functions > on board calibration

hi Rob,
  unfortunately seems so ...

  I personally do not see much benefit from this feature, really ... sorry

Hi Roger,
 thank you for email

few questions from me ...
1. how much people use such format? I'm not sure if I want to do some more complex task just for one person. Are these data available for public? Are periodically updated? etc ...
2. If I'll do some support for this, do you have some specification for this format? Seems it contain only areas defined by polygons correct? Anyway there is a lot of other parameters and some documentation should be more then useful ...

guys, some news are here viewtopic.php?f=13&t=377&start=20#p7968

hi guys,

so

1. I hope that map should NOT have to be orientated to north. Thanks to required three points, map should be orientated in any directory. But I haven't tried yet. Have you any sample that do not work? I'll check it ... (after few hours ...), uff mistake found. You was right, there was a problem ... should be fixed now

2. I found one issue after pressing "Compute" that might cause out of memory error, so it should be now also fixed (use testing version here)

3. anyway I currently need to load whole image to memory to work with it, so huge images may cause troubles. I still have no simple solution for this. Tested on Xoom, and loading of 4000x3000 huge image, took around 25MB of memory ... on normal phone, this is more then max memory that system allow locus to handle.

4. also I cannot find problem with displaying "Map item manager" dialog. May anyone create this testing version? Some changes was done there so it may help, otherwise log is needed. Also one important change. Created maps are now placed into locus/mapItems directory. After locus start you may start "Map item manager" (if will work) and here you can enable/disable maps you want without need to import (only as display) as it is currently.

5. glynta - I disabled anti-aliasing so now image should be sharper then before, try please

Also I was thinking about storing state of loaded maps between session. But due to problems with memory, I'll for now leave it as is, so you need after every start, load your own maps ...

[attachment=0:3nfsrpmi]1.14.5.2.apk[/attachment:3nfsrpmi]

hi,
  this feature is really in beta but it works in simple way
1. import KMZ file like in normal import
2. if will contain GroundOverlay layer, it will be displayed on map
3. to work with this layer (currently only hide/ show / delete), go to functions > map item manager
4. locus do not remember loaded overlays, so after you start locus again, you need to load it once more as in step 1.

Great  :mrgreen: I wanted this feature a lot. I have Maprika on my ...

glad you like it . Anyway there is button "Map" next to coordinates, where you can display map (with small overlay from photo). There is not need to define exact coordinates

its much better than "Map Calibrator". so i can delete this stuff now.
to calibrate from a reference-map is a great idea and works!

how can i save (and load) now various calibrated pictures/maps?

all calibrated maps are exported to "export" directory for now

Okay, I found how to calibrate a map, it shows...

Thank you for feedback, I'll surely improve it. Currently worst part is size of images ... that's maybe reason why app crashed to rijackson.

hi,
  I'm not at least a little familiar with winCE application Winpilot so I have no idea what data you want to use in Locus. Please specify a little and we can chat about it. Here in locus community is a lot of pilots as I know, so it should be interested topic for more people ...